Summary

This project contains a rin out sensor für RAISE3D printer.

Attention:

This projekt is in develop process

Print Settings

Printer:

Raise3D N2 Plus

                                            <p class="detail-setting rafts"><strong>Rafts: </strong>                     <div><p>No</p></div></p>                                                                                <p class="detail-setting supports"><strong>Supports: </strong>                     <div><p>Yes</p></div></p>                                                                                <p class="detail-setting resolution"><strong>Resolution: </strong>                     <div><p>0.2</p></div></p>                                                                                <p class="detail-setting infill"><strong>Infill: </strong>                     <div><p>35%</p></div></p>                                                        <br>                        <p class="detail-setting notes"><strong>Notes: </strong>                    </p><div><p>Filament: Polymaker PolyMax</p></div>

Custom Section

ESP8266 Software

            <div><p>/*<br>FILAMENT RUNOUT SENSOR FOR RAISE3D N2 Plus<br>Board: ESP8266 WeMos D1 mini<br>First version:  19.6.2018<br>Last change: 19.6.2018</p><p>TX Pin  1 PWM<br>RX Pin  3 PWM<br>D0 Pin 16 kein PWM (NICHT benutzbar)<br>D1 Pin  5 PWM (benutzbar)<br>D2 Pin  4 PWM (NICHT benutzbar)<br>D3 Pin  0 PWM (benutzbar)<br>D4 Pin  2 PWM (benutzbar) blue Led<br>D5 Pin 14 PWM (benutzbar)<br>D6 Pin 12 PWM (benutzbar)<br>D7 Pin 13 PWM (benutzbar) Install Pin Low install default value<br>D8 Pin 15 kein PWM (NICHT benutzbar)</p><p>static const uint8_t D0  = 16;<br>static const uint8_t D1  = 5;<br>static const uint8_t D2  = 4;<br>static const uint8_t D3  = 0;<br>static const uint8_t D4  = 2;<br>static const uint8_t D5  = 14;<br>static const uint8_t D6  = 12;<br>static const uint8_t D7  = 13;<br>static const uint8_t D8  = 15;<br>static const uint8_t D9  = 3;<br>static const uint8_t D10 = 1;<br>*/</p><h1>(&lt;)include ESP8266WiFi.h&gt;</h1><p>include WiFiClient.h<br>include WiFiServer.h<br>include WiFiUdp.h<br>include Metro.h</p><p>define PIN_SWITCH_LEFT   16<br>define PIN_SWITCH_RIGHT   5<br>define PIN_BUZZER            4  </p><p>// Adafruit Neopixel definition<br>include <br>define PIN_NEOPIXEL_DIO  12<br>define NEOPIXEL_LEDS      2<br>define LED_LEFT           0<br>define LED_RIGHT          1<br>Adafruit_NeoPixel strip = Adafruit_NeoPixel(NEOPIXEL_LEDS, PIN_NEOPIXEL_DIO, NEO_GRB + NEO_KHZ800);</p><p>uint32_t c_green  = strip.Color(  0,150,  0);<br>uint32_t c_red    = strip.Color(150,  0,  0);<br>uint32_t c_blue   = strip.Color(  0,  0,150);<br>uint32_t c_blank  = strip.Color(  0,  0,  0);<br>uint32_t c_orange = strip.Color(  0,150,150);</p><p>Metro Task1 = Metro(1000);  // Task 1 sec.</p><p>boolean switchLeftActive=false;<br>boolean switchRightActive=false;</p><h1>define FILAMENT_OUT 0</h1><h1>define FILAMENT_IN  1</h1><p>void setup() {<br>pinMode(PIN_SWITCH_LEFT, INPUT_PULLUP);<br>pinMode(PIN_SWITCH_RIGHT, INPUT_PULLUP);<br>Serial.begin(115200);<br>Serial.flush();<br>Serial.println("RAISE3D Filament Runout Sensor Modul version 1.0");<br>Serial.println();</p><p>if (digitalRead(PIN_SWITCH_LEFT) == FILAMENT_IN) switchLeftActive =true;<br>if (digitalRead(PIN_SWITCH_RIGHT)== FILAMENT_IN) switchRightActive=true;</p><p>if (switchLeftActive)  Serial.println("Sensor left is: ACTIV");  else Serial.println("Sensor left is: NOT ACTIV");<br>if (switchRightActive) Serial.println("Sensor right is: ACTIV"); else Serial.println("Sensor right is: NOT ACTIV");</p><p>Serial.println("Setup ready");<br>}</p><p>void loop() {</p><p>if (Task1.check() == 1) {</p><pre><code>// check switch leftif (switchLeftActive) {  if (digitalRead(PIN_SWITCH_LEFT)==FILAMENT_OUT) {    setStripLight(LED_LEFT, c_red);    Serial.print("Filament on the left side is out!");  } else setStripLight(LED_LEFT, c_green); } else setStripLight(LED_RIGHT, c_orange);// check switch rightif (switchRightActive) {  if (digitalRead(PIN_SWITCH_RIGHT)==FILAMENT_OUT) {    setStripLight(LED_RIGHT, c_red);    Serial.print("Filament on the right side is out!");  } else setStripLight(LED_RIGHT, c_green);} else setStripLight(LED_RIGHT, c_orange);</code></pre><p>}<br>}</p><p>void setStripLight(int num, uint32_t color) {<br>strip.setPixelColor(num, color);<br>strip.show();<br>}</p></div>

RAISE3D Filament run out sensor with ESP8266